74HC

Logic Is Power

.co.uk

RCMojo – Truck Light Controller – REV B

logo_1080_crop

lightControllerTruck_3

mojo_RCLights_Truck_B

  • 1x mojo_RCLights_Truck_B
  • 1x 2×8 Connector
  • 4x Servo Leads

£40.00

In Stock: 0

World LED Kit

Plug & Play LED Kit (World)

  • 1x 5mm White Type 1 (Headlights)
  • 1x 3mm White Type 1 (Reverse)
  • 2x 3mm Orange Type 2 (Indicators)
  • 2x 3mm Red Type 3 (Brake/Tail)

£20.00

Made to order

blank_product_image

Plug & Play LED Kit (USA)

  • 1x 5mm White Type 1 (Headlights)
  • 1x 3mm White Type 1 (Reverse)
  • 2x 3mm Orange Type 3 (Blinkers)
  • 2x 3mm Red Type 3 (Brake/Tail)

£18.00

Made to order

This board controls up to 8 channels of LEDs, rather than give you a wall of text it’ll be easier to break things up with a video and some pictures, needless to say, it’s a rather flexable bit of electronics!

.

top_crop

Requirements:

  • Minimum 2 channel radio, can be old 27MHz or modern 2.4GHz, or anywhere in between.
  • ESC with drag brake/crawler mode (X-Car 45A Brushed)
  • ESC with a switching BEC, or separate UBEC. 4.8v – 9v
  • LEDs must have their own resistor, the board is NOT compatible with Tamiya LED strings.

leds_crop

Startup Calibration:

leds_pcb

A couple of seconds after you power on the board one of the LEDs will turn on, if it’s red there is no input signal. If it’s green and rapidly flashing it’s trying to find the centre points of the channels, let go of the throttle and steering so they’re at their neutral point. Next the red LED will blink rapidly, move the throttle so you’re model moves forward.
If it’s been successful the green led will be solidly lit and the system armed and ready to use.

Channel Inputs:

inputs_crop

The 4 sets of 2×3 headers are the 4 Input Channels. Channel 1 is on the left, then 2, 3 and 4. The bottom pins connect to you receiver via the included leads, the top pins connect to your steering servo and ESC. The pins are marked on the board with S + -.

connectors_crop

Input Modes:

modes_crop_2

  • Basic – Only connect Channel Input 1 + 2
  • Classic – A + B
  • Inc/Dec – B + C
  • 2/3 Pos – No Junper

Basic:

Basic

This is for 2 channel radios, there’s no control over the LED mode All function are running, brake, reverse and indicators will all work.

Classic:

Classic_IncDec

Input Channel 3 connects to an AUX channel on a 2 position switch. First position is for normal operation. In the second position the red LED will blink rapidly and will allow the steering to increment and decrement the LED mode by moving away from centre.

Inc/Dec:

Classic_IncDec

Input Channel 3 connects to an AUX channel with a centre biased 3 position switch, moving the switch from the centre and back will increment or decrement the LED mode.

2/3 Pos:

2_3_Pos

Input channel 3 connects to an AUX channel with a 2 or 3 position switch. A 2 position switch will select Pos 1 or 3.

.

Note:

The Inc/Dec mode enables another trick, normally the indicators are tied to the steering. But in Inc/Dec mode you can connect Input Channel 1 to a channel controlled by a 3 position switch. This lets you control the indicators independently from the steering.

Output Modes:

outputs

  • World – A + B
  • World B – B + C
  • USA – No Jumper

World:

All functions are separate, this is the usual mode for RC lights.

World B:

Just like World, except the tail and brake lights are separated.

USA:

Indicators also flash the brake lights.


Download PDF Manual(1/12/14)

.
lightControllerTruck_3

mojo_RCLights_Truck_B

  • 1x mojo_RCLights_Truck_B
  • 1x 2×8 Connector
  • 4x Servo Leads

£40.00

In Stock: 0

World LED Kit

Plug & Play LED Kit (World)

  • 1x 5mm White Type 1 (Headlights)
  • 1x 3mm White Type 1 (Reverse)
  • 2x 3mm Orange Type 2 (Indicators)
  • 2x 3mm Red Type 3 (Brake/Tail)

£20.00

Made to order

blank_product_image

Plug & Play LED Kit (USA)

  • 1x 5mm White Type 1 (Headlights)
  • 1x 3mm White Type 1 (Reverse)
  • 2x 3mm Orange Type 3 (Blinkers)
  • 2x 3mm Red Type 3 (Brake/Tail)

£18.00

Made to order

.